Ürünlerimiz / Segmanlar / Inch Segmanlar / SHR Shaft Rings  

 

 

 : : : SHR MİL ÜSTÜ KALIN TİP EMNİYET SEGMANI INCH : : :
   

 

SHAFT DIAMETER GROOVE SIZE RING SIZE & WEIGHT CLEARANCE DIA. î THRUST LD. (lbs.)
Sqr. Corner Abutment
DIAMETER WIDTH DEPTH FREE 
DIAMETER		 THICKNESS
***		 Wght.
Per
1000
Pcs.		 Ex-
panded
over
shaft		 Released
in 
groove		 Ring
Safety
factor
of 4 		 Groove
Safety
factor 
of 2
Dh
DEC		 Ds
FRAC		 Ds
mm		 Dg Tol. W Tol. d  Df Tol. T Tol. lbs. L1 L2 Pr Pg
.394 - 10.0 .368 +.001 .039   .013 .362 +.003 .035   .70 .61 .58 2030 700
.428 - 10,9 .402 -.002 .039 +.003 .013 .394 -.008 .035   .86 .65 .62 2335 800
.473 - 12,0 .444 .002* .046 -.000 .015 .435   .042   1.4 .69 .66 3045 1000
.500 1/2 12,7 .468   .056   .016 .460   .050 ±.002 1.6 .75 .72 3959 1100
.591 - 15,0 .555   .056 +.004 .018 .543   .050   2.2 .86 .83 4568 1500
.625 5/8 15,9 .588   .056 -.000 .019 .575   .050   2.3 .90 .86 4872 1600
.669 - 17,0 .629   .056   .020 .616 +.005 .050   2.6 .94 .90 5278 1900
.750 3/4 19,0 .704 +.001 .086   .023 .689 -.010 .078   5.6 1.12 1.08 9135 2400
.787 - 20,0 .740 -.003 .086   .024 .689   .078   5.6 1.16 1.12 9135 2400
.875 7/8 22.2 .821 .002* .086   .027 .804   .078   7.5 1.25 1.20 10556 3300
.984 63/64 25,0 .925   .086   .030 .906   .078   7.8 1.36 1.30 11673 4000
1,000 1 25,4 .938   .086   .031 .906   .078   7.8 1.37 1.31 11673 4000
1,062 1-1/16 27,0 .998   .103   .032 .978   .093   11.5 1.52 1.46 15225 4800
1,125 1-1/8 28.6 1.059   .103 +.005 .033 1.036   .093 ±.003 12.5 1.58 1.52 16240 5200
1.181 - 30.0 1.111   .103 -.000 .035 1.087 +.010 .093   13.5 1.64 1.57 16748 5600
1.188 1-3/16 30,2 1.111 +.002 .103   .038 1.087 -.015 .093   13.5 1.64 1.57 16748 5600
1.250 1-1/4 31,7 1.174 -.004 .103   .038 1.150   .093   14.9 1.70 1.63 17763 6500
1,312 1-5/16 33,3 1.234 .004* .103   .039 1.208   .093   16.0 1.77 1.69 18270 7400
1,375 1-3/8 34,9 1.291   .103   .042 1.268   .093   17,8 1.83 1.75 19793 8200
1.378 - 35,0 1.291   .103   .044 1.268   .093   17.8 1.83 1.75 19793 8200
1.500 1-1/2 38,1 1.406   .120   .047 1.380   .109   27.0 2.08 1.98 24868 10000
1.562 1-9/16 39,7 1.468   .120   .047 1.437   .109   31.0 2.14 2.05 26390 10400
1.575 - 40,0 1.480   .120   .048 1.437   .109   31.0 2.15 2.06 26930 10400
1.750 1-3/4 44,4 1.650   .120   .050 1.608   .109   33.4 2.34 2.25 29435 12400
1.772 - 45,0 1.669 +.003 .120   .052 1.608 +.013 .109   33.4 2.37 2.27 29435 12400
1,938 1-15/16 49,2 1.826 -.004 .139   .056 1.782 -.020 .125 ±.004 48.0 2.58 2.48 37555 15300
1.969 1-31/32 50,0 1.850 .004* .139 +.006 .060 1.782   .125   48.0 2.61 2.50 37555 15300
2.000 2 50,8 1.880   .139 -.000 .060 1.840   .125   50,6 2.64 2,53 38570 17000
   
* F.I.M. (FULL INDICATOR MOVEMENT)- MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN GROOVE AND SHAFT.
î BASED ON HOUSINGS/SHAFTS MADE OF COLD ROLLED STEEL. FOR AN EXPLANATION OF FORMULAS USED TO DERIVE THRUST LOAD AND OTHER PERFORMANCE DATA CONTACT THE ROTOR CLIP ENGINEERING DEPARTMENT.
***FOR PLATED RINGS ADD .002" TO THE LISTED MAXIMUM THICKNESS. MAXIMUM RING THICKNESS WILL BE A MINIMUM OF .0002" LESS THAN THE LISTED GROOVE WIDTH (W) MINIMUM
    

 

 

LUG
HEIGHT		 MAXIMUM
SECTION		 MINIMUM
SECTION		 HOLE
DIAMETER		 GAGIN
DIA.

ALLOWABLE CORNER
RADII & CHAMFERS

 MAX LOAD
W/R Max
or Ch Max
(in lbs)		 EDGE
MARGINS		 R.P.M.
LIMITS 
Standart
material
H Tol. S max Tol. S min. Tol. R Tol. Gd Max R max Ch max P'r Y
,101   ,068   ,039   ,042   ,479 ,047 ,039 450 ,039 80000
,101   .076 ±.004 ,043 ±.004 .042   .525 .057 .046 530 .039 72000
,101 ±.004 ,088   ,053   ,042 +.010 ,589 ,070 ,058 550 ,045 69000
,120   .090   ,050   ,050 -.002 ,613 ,070 .058 650 ,048 65000
,130   ,102   ,057   ,050   ,719 ,070 ,058 750 ,054 52500
,130   ,106 ±.005 ,059 ±.005 ,050   ,758 ,074 ,062 750 ,057 49000
,130   ,112   ,062   ,050   ,808 ,077 ,064 900 ,060 45000
,180   ,127   ,077   ,078   ,913 ,089 ,074 2500 ,069 40500
,180   ,127   ,077   ,078   ,949 ,089 ,074 2500 ,072 38000
,180   ,148 ±.006 ,083 ±.006 ,078   1,056 ,100 ,083 2500 ,081 34000
,180   ,151   ,084   ,078   1,164 ,100 ,083 2500 ,090 30000
,180   ,151   ,084   ,078   1,177 ,100 ,083 2500 ,093 30000
,220   ,161   ,090   ,093   1,256 ,106 ,088 4000 ,096 27000
,220   ,169   ,095   ,093   1,329 ,112 ,093 4000 ,099 26000
,220   ,176   ,098   ,093   1,391 ,112 ,093 4000 ,105 24000
.220 ±.005 ,176 ±.007 ,098 ±.007 ,093   1,391 ,112 ,093 4000 .114 24000
,220   ,185   ,103   ,093   1,468 ,112 ,093 4000 ,114 23000
.220   ,192   ,106   ,093   1,538 ,128 ,107 4000 ,117 21500
,220   ,200   ,110   ,093   1,607 ,128 ,107 4000 ,126 20500
,220   ,200   ,110   ,093   1,607 ,128 ,107 4000 ,132 20500
,280   ,218   ,123   ,109 +.015 1,752 ,128 ,107 5000 ,141 18500
,280   ,228   ,127   ,109 -.002 1,829 ,128 ,107 5000 ,141 17000
,280   ,228   ,127   ,109   1,841 ,128 ,107 5000 ,144 17000
,290   .254 ±.008 .140 ±.008 ,109   2,050 ,128 ,107 5000 ,150 15500
,290   ,254   ,140   ,109   2,069 ,128 ,107 5000 ,156 15500
,314   ,280   ,154   ,125   2,265 ,153 ,128 6000 ,168 14300
,314 ±.006 ,280   ,154   ,125   2,289 ,153 ,128 6000 ,180 14100
,314   ,290   ,160   ,125   2,334 ,153 ,128 6000 ,180 14000
   
LARGER SIZES MAY BE AVAILABLE UPON REQUEST.