Ürünlerimiz / Segmanlar / Inch
Segmanlar / SHM
Housing Rings
|
|
|
|
|
|
: : : : : SHM Housing Rings : : : : : | |
|
|
|
SHAFT |
GROOVE SIZE | RING SIZE & WEIGHT | CLEARANCE DIA. |
î THRUST LD. |
||||||||||||
|
DIAMETER |
WIDTH | DEPTH | FREE DIAMETER |
THICKNESS *** |
Wght. Per 1000 Pcs. |
Expan- ded over shaft |
Released in groove |
Ring Safety Factor of 4 |
Groove Safety Factor of 2 |
|||||||
| Ds DEC |
Tol. | Ds FRACT |
Dg | Tol. | W | Tol. | d | Df | Tol. | T | Tol. | lbs. | L1 | L2 | Pr | Pg |
| ,101 | - | .093 | ±.001 | .024 | ,004 | ,090 | ,020 | .036 | .160 | ,152 | 30 | |||||
| ,125 | ±.001 | 1/8 | .115 | .0015* | .024 | +.002 | .005 | .112 | ,020 | .050 | .186 | .176 | 40 | |||
| ,134 | - | .124 | .024 | -.000 | ,005 | .120 | ±.002 | ,020 | .059 | .197 | ,187 | 45 | ||||
| ,156 | 5/32 | .144 | .029 | .006 | .140 | .025 | .122 | .252 | .240 | ** | 65 | |||||
| ,188 | 3/16 | .174 | .029 | .007 | .168 | .025 | .179 | .297 | .283 | SEE | 90 | |||||
| ,203 | 13/64 | .189 | .029 | .007 | .180 | .025 | ±.002 | .167 | .302 | .288 | NOTE | 100 | ||||
| ,219 | 7/32 | .205 | .039 | .007 | .200 | ±.003 | .035 | .334 | .345 | .331 | BELOW | 110 | ||||
| ,250 | 1/4 | .232 | ±.0015 | .039 | .009 | .224 | .035 | .386 | .384 | .366 | ** | 160 | ||||
| ,266 | 17/64 | .248 | +.002* | .039 | +.003 | .009 | .240 | .035 | .467 | .406 | .388 | 170 | ||||
| ,312 | ±.0015 | 5/16 | .292 | .039 | -.000 | .010 | .284 | .035 | .626 | .478 | .458 | 220 | ||||
| ,328 | 21/64 | .308 | .039 | .010 | .300 | .035 | .688 | .498 | .480 | 230 | ||||||
| ,375 | 3/8 | .351 | ±.002.002* | .046 | .012 | .340 | .042 | 1.035 | .567 | .543 | 315 | |||||
 |
* F.I.M. (FULL INDICATOR MOVEMENT)- MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN GROOVE AND SHAFT. |
|
î BASED ON HOUSINGS/SHAFTS MADE OF COLD ROLLED STEEL. FOR AN EXPLANATION OF FORMULAS USED TO DERIVE THRUST LOAD AND OTHER PERFORMANCE DATA CONTACT THE ROTOR CLIP ENGINEERING DEPT. |
|
***FOR PLATED RINGS ADD .002" TO THE LISTED MAXIMUM THICKNESS. MAXIMUM RING THICKNESS WILL BE A MINIMUM OF .0002" LESS THAN THE LISTED GROOVE WIDTH (W) MINIMUM |
|
**CALL FOR INFORMATION:1-800-557-6867 |
|
|
| S Max. | S Min. | GAGING DIA. |
ALLOWABLE CORNER RADII & |
MAX. LOAD w/ R max or Ch max. (in lbs.) |
EDGE MAR- GIN |
R.P.M. LIMITS Stand- ard material |
MANDREL | BUSHING
|
||||||||
| Ref. | Ref. | Gd Max |
R max |
Ch max | î
P'r (lbs.) |
Y |
Dp | Tol. | W ref. | G | Tol. | I.D. | Tol. | O.D. | ||
| .027 | .017 | .143 | .013 | .010 | .012 | 80000 | .102 | .036 | .750 | .104 | 3/8 | |||||
| .028 | .018 | .167 | .013 | .010 | .015 | 80000 | .126 | .059 | .750 | .128 | 3/8 | |||||
| .029 | .019 | .178 | .014 | .011 | .015 | 80000 | .135 | .069 | .750 | .137 | 3/8 | |||||
| .045 | .027 | .222 | .021 | .017 | .018 | 80000 | .157 | .078 | .875 | .159 | 1/2 | |||||
| .052 | .032 | .264 | .024 | .019 | SEE NOTE | .021 | 80000 | .189 | .110 | .875 | .191 | 1/2 | ||||
| .046 | .030 | .272 | .023 | .018 | ON | .021 | 80000 | .204 | +.000 | .125 | .875 | ±.005 | .206 | +.002 | 1/2 | |
| .058 | .036 | .308 | .028 | .022 | PREVIOUS | .021 | 80000 | .221 | -.0015 | .129 | 1.000 | .223 | -.000 | 1/2 | ||
| .063 | .037 | .340 | .028 | .022 | PAGE | .027 | 80000 | .252 | .101 | 1.000 | .254 | 5/8 | ||||
| .065 | .037 | .359 | .027 | .022 | .027 | 80000 | .268 | .176 | 1.000 | .270 | 5/8 | |||||
| .078 | .050 | .431 | .038 | .030 | .030 | 80000 | .314 | .223 | 1.000 | .316 | 5/8 | |||||
| .080 | .050 | .448 | .038 | .030 | .030 | 80000 | .330 | .238 | 1.000 | .332 | 5/8 | |||||
| .090 | .058 | .511 | .042 | .033 | .036 | 80000 | .377 | .286 | 1.000 | .379 | 5/8 | |||||
|
LARGER SIZES MAY BE AVAILABLE UPON REQUEST. |
