Ürünlerimiz / Segmanlar / Inch
Segmanlar /
SHF Rings
|
|
|
|
|
|
: : : : : SHF GENİŞ TİP EMNİYET SEGMANI INCH : : : : : | |
|
|
| SHAFT DIAMETER |
GROOVE SIZE | RING SIZE & WEIGHT | CLEAR. | î THRUST LD.(lbs.) Sqr. corner abutment | ||||||||||||
| DIAMETER | WIDTH | DEPTH | FREE DIAMETER
|
THICKNESS*** | Weight Per 1000 Pcs. | Released over shaft | Allow- able load (lbs.) | Groove Safety factor of 2 | ||||||||
| Ds DEC | Ds FRACT | Ds mm | Dg | Tol. | W | Tol. | d | Df | Tol. | T | Tol. | lbs. | L2 | Pr | Pg | |
| FROM | TO | |||||||||||||||
| .058 | .060 | - | 1.5 | not
recommended for use with grooves |
,055 | +.002 | ,015 | .030 | .21 | 5 | not recommended for use with grooves | |||||
| .078 | .080 | 5/64 | 2,0 | ,074 | -.003 | ,025 | .08 | .24 | 8 | |||||||
| .092 | .096 | 3/32 | 2,4 | ,089 | ,025 | ±.002 | .10 | .26 | 8 | |||||||
| .123 | .127 | 1/8 | 3,2 | ,120 | ,025 | .24 | .33 | 10 | ||||||||
| .154 | .158 | 5/32 | 4,0 | ,150 | +.002 | ,025 | .30 | .36 | 12 | |||||||
| .185 | .189 | 3/16 | 4,8 | .181 | -.004 | ,035 | .55 | .44 | 20 | |||||||
| .195 | .199 | - | 5,0 | .187 | ±.003 | ,032 | .45 | .43 | 30 | |||||||
| .234 | .238 | 15/64 | 6,0 | .228 | +.0005 | .041 | +.003 | .004 | ,224 | ,035 | ±.003 | .76 | .48 | 22 | 70 | |
| .248 | .252 | 1/4 | 6,3 | .240 | -.0015 | .041 | -.000 | .005 | .238 | +.002-.004 | ,035 | .74 | .49 | 23 | 90 | |
| .310 | .316 | 5/16 | 7,9 | .303 | .048 | .005 | ,298 | ,042 | 1.39 | .68 | 25 | 110 | ||||
| .373 | .379 | 3/8 | 9,5 | .361 | +.001 | .048 | .007 | ,354 | +.003 | ,042 | 1.72 | .74 | 31 | 180 | ||
| .434 | .440 | 7/16 | 11.0 | .419 | -.002 | .056 | +.004 | .009 | ,412 | -.005 | ,050 | 2.61 | .81 | 41 | 290 | |
| .497 | .503 | 1/2 | 12.7 | .478 | .056 | -.000 | .011 | .470 | +.004 | ,050 | 2.91 | .90 | 46 | 390 | ||
| .622 | .628 | 5/8 | 15.9 | .599 | .069 | .013 | .593 | -.006 | ,062 | ±.004 | 5.70 | 1.06 | 61 | 570 | ||
| .745 | .755 | 3/4 | 19.0 | .718 | +.002-.003 | .069 | .016 | .706 | ,062 | 6.88 | 1.32 | 66 | 850 | |||
 |
î VALUES SHOWN APPLY TO RINGS INSTALLED ON A SHAFT MADE OF LOW CARBON STEEL. |
|
FOR AN EXPLANATION OF FORMULAS USED TO DERIVE THRUST LOAD AND OTHER PERFORMANCE DATA, CONTACT THE ROTOR CLIP ENGINEERING DEPARTMENT. |
|
***FOR PLATED RINGS, ADD.002" TO THE LISTED MAXIMUM THICKNESS. |
|
MAXIMUM RING THICKNESS ( WHEN USED IN GROOVE) WILL BE A MINIMUM OF .0002" LESS THAN THE LISTED GROOVE WIDTH (W) MINIMUM. |
|
|
| ALLOWABLE CORNER RADII & CHAMFERS |
EDGE MARGIN | LUG | HOLE | RING HEIGHT |
R.P.M. LIMITS Standard material |
|||
| R max | Ch max | Y | H | Tol. | R | Tol. | B | |
| .025 | .015 | NOT
RECOMMENDED
FOR USE WITH GROOVES |
.066 | ±.005 | .035 | .145 | OVER
80000 |
|
| .036 | .022 | .071 | .034 | ±.004 | .184 | |||
| .042 | .025 | .074 | .034 | .207 | ||||
| .054 | .032 | .078 | .042 | +.010 | .268 | |||
| .059 | .035 | .078 | ±.003 | .042 | -.002 | .307 | ||
| .063 | .038 | .097 | .051 | .364 | ||||
| .064 | .039 | .104 | ±.008 | .051 | ±.004 | .375 | ||
| .070 | .042 | .030 | .098 | ±.003 | .051 | +.010 | .422 | |
| .072 | .043 | .030 | .097 | .051 | -.002 | .437 | 77000 | |
| .080 | .048 | .030 | .141 | .078 | .553 | 58000 | ||
| .086 | .051 | .030 | .141 | ±.004 | .078 | .620 | 51000 | |
| .093 | .056 | .030 | .151 | .078 | +.015 | .701 | 44000 | |
| .100 | .060 | .040 | .158 | .078 | -.002 | .768 | 40000 | |
| .120 | .072 | .045 | .180 | .078 | .948 | 32000 | ||
| .125 | .075 | .050 | .233 | .120 | 1.115 | 25000 | ||
|
LARGER SIZES MAY BE AVAILABLE UPON REQUEST. |
|
FOR HARDNESS SPECIFICATIONS, SEE END OF THIS SECTION. |
