Ürünlerimiz / Segmanlar / Inch Segmanlar / HO Housing Rings 2  

 

 

 : : : : : HO Housing Rings 2 : : : : :
 

 | HO Housing Rings 1 | HO Housing Rings 3 |

  
HOUSING GROOVE SIZE RING SIZE & WEIGHT CLEARANCE DIA. î THRUST LD. (lbs.) 
Sqr. corner abutment
 DIAMETER   DIAMETER   WIDTH DEPTH  Free
Diameter		 Thickness
***		 Wght.
Per
1000
Pcs.		 Com-
pressed
in housing		 Re-
leased
in groove		 Ring Safety Factor  
of 4		 Groove Safety Factor
of 2
Dh DEC Dh FRAC Dh mm
Dg Tol. W Tol. d Df Tol. T Tol. lbs. L1 L2 Pr Pg
1,750 1-3/4 44,4 1,858 ±.005 ,068 +.004 ,054 1,942 +.035 ,062   10,3 1,26 1,36 15580 8050
1,812 1-13/16 46,0 1,922 .005* ,068 -.000 ,055 2,012 -.025 ,062   11,5 1,34 1,38 16139 8450
1,850 - 47,0 1,962   ,068   ,056 2,054   ,062   12,8 1,35 1,46 16443 8750
1,875 1-7/8 47,6 1.989   ,068   ,057 2,072   ,062   12,8 1,37 1.48 16697 9050
1,938 1-15/16 49,2 2,056   ,068   ,059 2,141   ,062   13,3 1,46 1,58 17255 9700
2,000 2 50,8 2.122   ,068   .061 2.210   ,062   14,0 1,52 1,64 17763 10300
2,047 - 52,0 2.171   ,086   ,062 2,280   ,078   18,0 1,52 1,64 23091 10850
2,062 2-1/16 52,4 2.186   ,086   ,062 2,280   ,078   18,0 1.54 1.66 23091 10850
2,125 2-1/8 54,0 2,251   ,086   ,063 2,350   ,078   19,4 1,58 1,70 23751 11350
2,165 - 55,0 2.295   ,086   .065 2.415   ,078   19,6 1,63 1,75 24461 12050
2,188 2-3/16 55,6 2.318   ,086   .065 2.415   ,078   19,6 1,66 1,79 24461 12050
2,250 2-1/4 57,1 2.382   ,086   .066 2.490   ,078   21,8 1,67 1,80 25223 12600
2,312 2-5/16 58,7 2,450   ,086   .069 2.560   ,078   22,6 1,73 1,93 25832 13550
2,375 2-3/8 60,3 2.517   ,086   .071 2,630   ,078 ±.003 23,2 1,79 1,86 26542 14300
2,440 2-7/16 62,0 2,584   ,086   ,072 2,702 +.040 ,078   25,4 1,86 2,00 27304 14900
2,500 2-1/2 63,5 2.648   ,086   ,074 2,775 -.030 ,078   25,5 1,91 2,05 28014 15650
2,531 2-17/32 64,3 2,681   ,086   ,075 2,775   ,078   25,5 1,94 2,09 28014 15650
2,562 2-9/16 65,1 2.714   ,103   .076 2,844   ,093   34,0 1,93 2,08 34206 16500
2,625 2-5/8 66,7 2,781 ±.006 ,103 +.005 ,078 2,910   ,093   34,5 2,02 2,17 35068 17350
2,677 - 68,0 2,837 .006* ,103 -.000 .080 2,980   ,093   35,0 2,05 2,21 35931 18250
2,688 2-11/16 68,3 2,848   ,103   ,080 2,980   ,093   35,0 2,06 2,22 35931 18250
2,750 2-3/4 69,8 2,914   ,103   ,082 3,050   ,093   35,5 2,12 2,28 36642 19200
2,812 2-13/16 71.4 2,980   ,103   ,084 3,121   ,093   36,0 2,18 2,34 37504 20050
2,835 - 72,0 3.006   ,103   ,085 3,121   ,093   36,0 2.21 2,38 37504 20050
2,875 2-7/8 73,0 3.051   ,103   ,088 3,191   ,093   41,0 2,24 2,41 38367 21500
2,953 - 75,0 3.135   ,103   .091 3.325   ,093   42,5 2,32 2,50 40093 23150
3,000 3 76,2 3,182   ,103   ,091 3,325   ,093   42,5 2,37 2,55 40093 23150
3,062 3-1/16 77.8 3.248   ,120   .093 3.418   .109   53.0 2,41 2.59 47807 24100
3,125 3-1/8 79,4 3,315   ,120   ,095 3,488   ,109   56,0 2,47 2,66 48822 25200
3,149 - 80,0 3,341   ,120   ,096 3,523   ,109   57,0 2,49 2,68 49329 25700
3,156 3-5/32 80,2 3,348   ,120   ,096 3,523 ±.055 ,109   57,0 2,50 2,69 49329 25700
3,250 3-1/4 82,5 3,446   ,120   ,098 3,623   ,109   60,0 2,54 2,73 50750 27000
3,346 3-11/32 85,0 3,546   ,120   ,100 3,734   ,109   65,0 2,63 2,83 52374 28300
3,469 3-15/32 88.1 3,675   ,120   ,103 3,857   ,109   69,0 2,76 2,96 54201 30200
3,500 3-1/2 88,9 3.710   ,120   ,105 3,890   ,109   71,0 2,79 3,00 54709 31200
   
* F.I.M. (FULL INDICATOR MOVEMENT)- MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN GROOVE & HOUSING.
î BASED ON HOUSINGS/SHAFTS MADE OF COLD ROLLED STEEL. FOR AN EXPLANATION OF FORMULAS USED TO DERIVE THRUST LOAD AND OTHER PERFORMANCE DATA CONTACT THE ROTOR CLIP ENGINEERING DEPARTMENT.
***FOR PLATED RINGS ADD .002" TO THE LISTED MAXIMUM THICKNESS. MAXIMUM THICKNESS WILL BE A MINIMUM OF .0002" LESS THAN THE LISTED GROOVE WIDTH (W) MINIMUM.
    

 

 

 

LUG
HEIGHT		 MAXIMUM SECTION

MINIMUM SECTION

 

 HOLE DIAMETER

 

 GAP
WIDTH Ring in Groove		 ALLOWABLE CORNER RADII & CHAMFERS MAX. LOAD  
w/R max or Ch
max (lbs.)		 EDGE
MARGIN
H Tol. S max Tol. S min Tol. R Tol. G Min R max Ch max P'r Y
,230   ,170   .083   .078   .372 .064 .050 3900 .162
,230   .170   .084   .093   .382 .064 .050 3900 .165
,234   .170   .085   .093   .360 .064 .050 3900 .168
,234   .170   .085   .093   .430 .064 .050 3900 .171
,230   .170   .085   .093   .438 .064 .050 3900 .177
,230   .170   .085   .093   .453 .064 .050 3900 .183
,250   .186   .091   .093   .428 .078 .061 6200 .186
.250 ±.005 .186 ±.007 .091 ±.007 .093 +.015 .468 .078 .062 6200 .186
,250   .195   .096   .093 -.002 .460 .078 .062 6200 .189
,250   .199   .098   .093   .439 .078 .062 6200 .195
.250   .199   .098   .093   .489 .078 .062 6200 .195
.280   .203   .099   .093   .478 .078 .062 6200 .198
.280   .206   .100   .093   .486 .078 .062 6200 .207
.280   .207   .102   .093   .504 .078 .062 6200 .213
,280   .209   .103   .110   .518 .078 .062 6200 .216
,280   .210   .103   .110   .532 .078 .062 6200 .222
,280   .210   .103   .110   .597 .078 .062 6200 .225
.300   .222   .109   .110   .540 .088 .070 9000 .228
,290   .226   .111   .110   .558 .088 .070 9000 .234
,300   .230   .113   .110   .539 .090 .072 9000 .240
,300   .230   .113   .110   .568 .090 .072 9000 .240
,300   .234   .115   .110   .590 .092 .074 9000 .246
,300   .230   .115   .110   .615 .088 .070 9000 .252
.300   .230   .115   .110   .676 .088 .070 9000 .255
,300   .240   .120   .110   .626 .092 .074 9000 .264
.300   .250   .122   .110   .619 .092 .074 9000 .273
.300   .250   .122   .110   .738 .092 .074 9000 .273
,310   .254   .126   .125   .651 .097 .078 12000 .279
,310   .259   .129   .125   .655 .099 .079 12000 .285
,310   .262   .129   .125   .650 .100 .080 12000 .288
,310   .262   .129   .125   .669 .100 .080 12000 .288
,342   .269   .135   .125   .698 .104 .083 12000 .294
,342 ±.008 .276 ±.008 .140 ±.008 .125   .705 .108 .086 12000 .300
,342   .286   .144   .125   .763 .108 .086 12000 .309
,342   .289   .142   .125   .774 .110 .088 12000 .315
   
FOR HARDNESS SPECIFICATIONS, SEE END OF THIS SECTION