Ürünlerimiz / Segmanlar / Inch Segmanlar / BSH   

 

 

 : : : : : BSH HAVŞA TİP EMNİYET SEGMANI INCH : : : : :
   

 

SHAFT

GROOVE SIZE

 RING SIZE & WEIGHT

CLEAR. DIA.

î THRUST LD. (lbs.)
Sqr. Corner Abutment

Diameter

Diameter

Width

Depth 

  Free Diameter

Thickness
***

 Bow Height

Wght.
Per
1000
Pcs.

Ex- 
panded
over
shaft

Released 
in 
groove

 RING
Safety
Factor
of 4		 GROOVE
Safety
Factor
of 2
Ds
DEC		 Ds
FRACT		 Ds
mm		 Dg Tol. W Tol. d Df Tol. T Tol. Bh Tol. lbs. L1 L2 Pr Pg
.250 1/4 6.4 .230

±.0015.
0015*

 .040    .010 .225

+.002
-.004

 .025    .047   .21 .45 .43 599 175
.276 - 7.0 .255   .040   .010 .250   .025   .047   .23 .48 .46 660 195
.281 9/32 7.1 .261   .040   .010 .256   .025   .047   .24 .49 .47 670 200
,312 5/16 7.9 .290   .040   .011 .281   .025   .047   .27 .54 .52 751 240
,344 11/32 8.7 .321   .040   .011 .309   .025   .047   .31 .57 .55 812 265
,354 - 9.0 .330

±.002

 .040   .012 .320 +.002 .025 ±.002 .047 ±.006 .35 .59 .57 832 300
,375 3/8 9.5 .352

.002*

 .040   .012 .338 -.005 .025   .047   .39 .61 .59 883 325
,394 - 10.0 .369   .040   .012 .354   .025   .047   .42 .62 .60 954 335
,406 13/32 10.3 .382   .040   .012 .366   .025   .047   .43 .63 .61 964 350
,438 7/16 11.1 .412   .040   .013 .395   .025   .047   .50 .66 .64 1035 400
,469 15/32 11.9 .443   .040   .013 .428   .025   .047   .54 .68 .66 1117 450
,500 1/2 12.7 .468   .055   .016 .461   .035   .063   .91 .77 .74 1675 550
,551 - 14.0 .519 ±.002 .055 +.003 .016 .509   ,035   .063 ±.007 .90 .81 .78 1827 600
,562 9/16 14.3 .530

.004*

 .055 -.000 .016 .521   ,035   .063   1.1 .82 .79 1878 650
,594 19/32 15.1 .559   .055   .017 .550   ,035   .063   1.2 .86 .83 1979 750
,625 5/8 15.9 .588   .055   .018 .579   ,035   .063   1.3 .90 .87 2091 800
,669 - 17.0 .629   .055   .020 .621   ,035   .063   1.4 .93 .89 2233 950
,672 43/64 17.1 .631   .055   .020 .621   ,035   .063   1.4 .93 .89 2233 950
,688 11/16 17.5 .646 ±.003 .062   .021 .635 +.005 ,042   .073 ±.008 1.8 1.01 .97 3451 1000
,750 3/4 19.0 .704 .004* .062   .023 .693 -.010 ,042   .073   2.1 1,09 1.05 3756 1200
,781 25/32 19.8 .733   .062   .024 .722   ,042   .073   2.2 1.12 1.08 3959 1300
,812 13/16 20.6 .762   .062   .025 .751   ,042   .073   2.5 1.15 1.10 4060 1450
,875 7/8 22.2 .821   .062   .027 .810   ,042   .073   2.8 1.21 1.16 4365 1650
,938 15/16 23.8 .882   .062   .028 .867   ,042   .073   3.1 1,34 1.29 4720 1850
,984 63/64 25.0 .926   .062   .029 .910   ,042   .073   3.5 1.39 1.34 4923 2000
1,000 1 25.4 .940   .062   .030 .925   ,042   .073   3.6 1.41 1.35 5024 2100
1,023 - 26.0 .961   .062   .031 .946   ,042   .073   3.9 1.43 1.37 5126 2250
1,062 1-1/16 27.0 .998   .070   .032 .982   ,050   .085   4.8 1,50 1.44 6293 2400
1,125 1-1/8 28.6 1.059   .070   .033 1.041   ,050   .085   5.1 1.55 1.49 6699 2600
1,188 1-3/16 30.2 1.118   .070   .035 1.098   ,050   .085   5.6 1,61 1.54 7105 2950
1,250 1-1/4 31.7 1.176   .070   .037 1.156   ,050   .085   5.9 1,69 1.62 7460 3250
1,312 1-5/16 33.3 1.232 ±.004 .070   .040 1.214 +.010 ,050   .085 ±.012 6.8 1,75 1.67 7866 3700
1,375 1-3/8 34.9 1.291 .005* .070   .042 1.272 -.015 ,050   .085   7.2 1,80 1.72 8222 4100
1,438 1-7/16 36.5 1.350   .070   .044 1.333   ,050   .085   8.1 1,87 1.79 8628 4500
1,500 1-1/2 38.1 1.406   .070   .047 1.387   ,050   .085   9.0 1,99 1.90 8932 5000
1,625 1-5/8 41.3 1.529 ±.005 .096 +.005 .048 1.503 +.013 ,062 ±.003 .115 ±.015 13.2 2,17 2.08 12028 5500
1,750 1-3/4 44.4 1.650 .005* .096 -.000 .050 1,618 -.020 ,062   .115   15.3 2,31 2.21 12992 6200
   
*F.I.M. (FULL INDICATOR MOVEMENT)-MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN GROOVE AND SHAFT.
î BASED ON HOUSINGS/SHAFTS MADE OF COLD ROLLED STEEL. FOR AN EXPLANATION OF FORMULAS USED TO DERIVE THRUST LOAD AND OTHER PERFORMANCE DATA, CONTACT THE ROTOR CLIP ENGINEERING DEPT. 
***FOR PLATED RINGS, ADD .002" TO THE LISTED MAXIMUM THICKNESS.  
   

 

 

DISTANCE Outer groove wall to face of retained part

TAKEUP Resili-
ent takeup
of tole-
rances

FORCE 
Needed to flatten rings

ALLOWABLE 
CORNER RADII
& CHAMFERS

MAX. 
LOAD
w/ R max 
or
Ch max (in lbs.)

EDGE
MARGIN

LUG
HEIGHT

 MAXIMUM
SECTION

MINIMUM
SECTION

HOLE DIAMETER

GAG-ING DIA.

R.P.M 
LIMITS Standard material

 

 
J min J max J max
J min		 lbs. R max Ch
max		 P'r
(lbs.)		 Y H Tol. S max Tol. S min Tol. R  Tol. Gd Max
.030 .038   50 .018 .011 470 .030 .080   .035   .025   .041   .290 80000
.030 .038   50 .0175 .0105 470 .031 .081   .035   .024   .041   .315 76000
.030 .038   50 .020 .012 470 .030 .080   .038   .0255   .041   .326 74000
.030 .038   50 .020 .012 470 .033 .087   .040   .026   .041   .357 70000
.030 .038   45 .021 .0125 470 .033 .087   .042   .0265   .041   .390 64000
.030 .038

.008

 45 .023 .014 470 .036 .087 ±.003 .046 ±.003 .029 ±.003 .041 +.010 .405 62000
.030 .038   45 .026 .0155 470 .036 .088   .050   .0305   .041 -.002 .433 60000
.030 .038   40 .027 .016 470 .037 .087   .052   .031   .041   .452 56500
.030 .038   40 .0285 .017 470 .036 .087   .054   .033   .041   .468 55000
.030 .038   35 .029 .0175 470 .039 .088   .055   .033   .041   .501 50000
.030 .038   35 .031 .018 470 .039 .088   .060   .035   .041   .540 42000
.042 .053   90 .034 .020 910 .048 .108   .065   .040   .047   .574 40000
.042 .053   85 .027 .0165 910 .048 .108   .053   .036   .047   .611 36000
.042 .053   80 .038 .023 910 .048 .108   .072 ±.004 .041 ±.004 .047   .644 35000
.042 .053   70 .0395 .0235 910 .052 .109   .076   .043   .047   .680 32000
.042 .053   60 .0415 .025 910 .055 .110   .080   .045   .047   .715 30000
.042 .053   50 .040 .024 910 .060 .110   .082   .043   .047   .756 29000
.042 .053   50 .040 .024 910 .060 .110   .082   .043   .047   .758 29000
.049 .060   70 .042 .025 1340 .063 .136   .084   .048   .052   .779 28000
.049 .060   65 .046 .0275 1340 .069 .136   .092   .051   .052   .850 26500
.049 .060   60 .047 .028 1340 .072 .136   .094   .052   .052   .883 25500
.049 .060   55 .047 .028 1340 .075 .136   .096   .054   .052   .914 24500
.049 .060   45 .051 .035 1340 .081 .137   .104 ±.005 .057 ±.005 .052   .987 23000
.049 .060   40 .055 .033 1340 .084 .166   .110   .063   .078   1.054 21500
.049 .060

.011

 40 .056 .0335 1340 .087 .167   .114   .0645   .078   1.106 20500
.049 .060   35 .057 .034 1340 .090 .167 ±.004 .116   .065   .078   1.122 20000
.049 .060   35 .058 .035 1340 .093 .168   .118   .066   .078   1.147 19500
.057 .068   60 .060 .036 1950 .096 .181   .122   .069   .078   1.192 19000
.057 .068   55 .063 .038 1950 .099 .182   .128   .071   .078   1.261 18800
.057 .068   50 .064 .0385 1950 .105 .182   .132   .072   .078 +.015 1.325 18000
.057 .068   45 .068 .041 1950 .111 .183   .140   .076   .078 -.002 1.396 17000
.057 .068   40 .068 .041 1950 .120 .183   .146 ±.006 .0765 ±.006 .078    1.458 16500
.057 .068   35 .072 .043 1950 .126 .184   .152   .082   .078   1.529 16000
.057 .068   30 .076 .045 1950 .132 .184   .160   .086   .078   1.600 15000
.057 .068   30 .079 .047 1950 .141 .214   .168   .091   .120   1.668 14800
.069 .094

.025

 55 .087 .052 3000 .144 .235   .180    .097    .125    1.812 13200
.069 .094   50 .091 .054 3000 .150 .237   .188   .101   .125   1.945 12200
   
LARGER SIZES MAY BE AVAILABLE UPON REQUEST.